Choosing EEG Electrodes and Montages: Selecting the Right Recording Strategy

Christian Burgos

Updated on

Nov 12, 2026

Choosing EEG Electrodes and Montages: Selecting the Right Recording Strategy

Christian Burgos

Updated on

Nov 12, 2026

Choosing EEG Electrodes and Montages: Selecting the Right Recording Strategy

Christian Burgos

Updated on

Nov 12, 2026

Introduction

The placement of EEG electrodes influences the types of neural activity researchers can observe and how experimental findings are interpreted. While selecting an EEG system is an important part of study planning, deciding where to record brain activity is equally critical. Electrode placement should always be guided by the research question rather than convenience or hardware specifications.

Different cognitive processes engage different brain regions, and no single electrode configuration is appropriate for every study. Researchers investigating visual perception may prioritize occipital regions, while studies of executive function often emphasize frontal activity. Other experiments may require broad cortical coverage to explore distributed neural networks.

This guide introduces common EEG electrode placement systems, explains how montages influence data collection, and discusses practical considerations for selecting recording locations that support the scientific objectives of a study.

Understanding Electrode Placement

EEG electrodes detect changes in electrical potential at the scalp generated by underlying neural activity. Because these signals are measured from multiple locations across the head, electrode placement determines which regions of cortical activity are sampled during an experiment.

Most EEG research follows standardized placement systems that allow recordings to be reproduced and compared across laboratories. Consistent electrode positioning also improves collaboration and facilitates interpretation of published findings.

Rather than attempting to measure every possible brain region, researchers should select electrode locations that best address their experimental hypotheses while considering practical constraints such as participant comfort, setup time, and recording quality.

The International 10-20 System

The International 10-20 System is the most widely used framework for positioning EEG electrodes. It defines standardized recording locations based on anatomical landmarks and proportional distances across the scalp, allowing researchers to reproduce electrode placement consistently across participants and studies [1].

Electrode labels correspond to general cortical regions. Frontal electrodes are identified with F, central with C, parietal with P, occipital with O, and temporal with T. Midline electrodes include the letter z, while odd numbers represent locations on the left hemisphere and even numbers indicate corresponding positions on the right.

Using standardized placement systems improves communication between researchers and helps ensure that published findings can be replicated using comparable recording configurations.

Top-down diagram of a head showing EEG electrode positions in the 10-20 system, color-coded by frontal, central, parietal, temporal and occipital regions, with a nasion-to-inion scale marking the 10% and 20% spacing intervals.

Label

Scalp region

Commonly studied in

Example sites

F

Frontal

Executive function, attention, decision-making

F3, F4, Fz

C

Central

Sensorimotor processes

C3, C4, Cz

P

Parietal

Attention, spatial processing, working memory

P3, P4, Pz

O

Occipital

Visual processing

O1, O2

T

Temporal

Auditory and language processing

T7, T8

z (suffix)

Midline

Activity along the scalp's center line

Fz, Cz, Pz

Odd number

Left hemisphere

Left-side counterpart of a site

F3, P7, O1

Even number

Right hemisphere

Right-side counterpart of a site

F4, P8, O2

Choosing Electrode Locations Based on the Research Question

Electrode selection should always begin with the scientific question rather than the available hardware.

Studies investigating visual processing often prioritize occipital electrodes because these regions are closely associated with visual information processing. Research involving executive function, attention, and decision-making frequently focuses on frontal regions, while sensorimotor studies may emphasize central electrodes.

Some experiments require broad cortical coverage because multiple brain regions contribute to the cognitive process under investigation. Others may focus on a smaller set of strategically selected electrodes when the neural mechanisms are already well understood.

Matching electrode placement to the experimental objectives improves both recording efficiency and interpretation of the resulting data.

Understanding Montages

A montage describes how EEG signals are referenced and displayed during recording or analysis. Although electrode placement determines where signals are collected, the selected montage influences how those signals are compared and interpreted.

Common reference strategies include common reference, average reference, linked mastoids, and bipolar montages. Each approach offers advantages depending on the experimental design and research objectives [1].

Because different reference strategies may influence waveform appearance, researchers should document the selected montage clearly when reporting experimental methods.

Four head diagrams comparing EEG montage types: common reference, average reference, linked mastoids and bipolar, each showing how its electrodes are connected.

Reference strategy

Each channel is compared against

Strengths

Watch out for

Common reference

A single shared electrode

Simple, consistent across channels

Activity at the reference site appears in every channel

Average reference

The mean of all recording electrodes

No single reference site dominates

Works best with dense, even coverage; less suited to low channel counts

Linked mastoids

The average of both mastoid sites

Widely used in ERP research; eases comparison with published work

Mastoids are not fully neutral and can pick up muscle activity

Bipolar

An adjacent electrode, in chained pairs

Highlights local differences between neighboring sites

Suppresses activity shared across neighboring electrodes

Channel Count and Spatial Coverage

Researchers often assume that increasing the number of electrodes automatically improves data quality. In practice, the appropriate channel count depends on the scientific objectives of the study.

Experiments investigating broad cortical networks or spatial patterns of neural activity may benefit from greater electrode coverage. Other studies, particularly those focusing on well-characterized cognitive processes or applied human factors research, may obtain meaningful results using fewer recording channels when those channels are positioned appropriately.

Selecting more electrodes than necessary increases setup time, participant burden, and data processing requirements without always providing additional scientific value.

The most effective recording strategy balances spatial coverage with the practical requirements of the experiment.

Electrode Placement in Mobile EEG Research

Wireless EEG has expanded opportunities to investigate cognition outside traditional laboratory environments. Mobile recording introduces additional practical considerations because participant movement, comfort, and recording duration become increasingly important.

Researchers designing classroom studies, workplace assessments, field research, or other naturalistic experiments often prioritize recording configurations that combine stable signal quality with efficient setup and participant comfort [2], [3].

Selecting an electrode configuration that supports both the scientific objectives and the recording environment helps maximize data quality throughout the study.

Matching the EEG System to the Study

After determining the required electrode locations and overall recording strategy, researchers can select an EEG system that supports those methodological needs.

Studies requiring rapid deployment or streamlined experimental workflows may benefit from systems with fewer electrodes positioned to capture commonly investigated cortical regions. Research requiring broader spatial coverage, event-related potentials, or more advanced cognitive analyses may benefit from systems that support additional recording channels and greater flexibility.

Rather than asking which EEG system is the most advanced, researchers should consider which system best supports the experimental questions they intend to answer.

System

Recording channels

Recording sites

Reference placement

Insight

5

AF3, AF4, T7, T8, Pz

CMS/DRL on left mastoid

Epoc X

14

AF3, F7, F3, FC5, T7, P7, O1, O2, P8, T8, FC6, F4, F8, AF4

CMS/DRL at P3/P4 (mastoids as alternative)

EPOC X PRO

16

Epoc X's 14 sites plus P3 and P4

CMS left mastoid, DRL right mastoid (fixed)

Flex 2 (Saline or Gel)

Up to 32, configurable

Any of 74 cap openings at standard 10-20 positions

CMS/DRL at any 10-20 location or on the ears

Side-by-side head diagrams of the EPOC X and EPOC X PRO electrode layouts, with the two added P3 and P4 sensors highlighted in blue to show the PRO’s added parietal and visual coverage.

Reporting Electrode Placement

Transparent reporting is an essential component of reproducible EEG research. Researchers should document the electrode placement system, recording montage, reference strategy, channel configuration, and any deviations from standardized placement procedures.

Providing this information allows other investigators to evaluate the methodology, reproduce the experiment, and compare findings across studies.

Clear methodological reporting strengthens both individual studies and the broader scientific literature.

Key Takeaways

Electrode placement is a fundamental component of experimental design. Choosing appropriate recording locations and montages helps ensure that EEG data accurately reflect the cognitive processes being investigated.

Researchers should select electrode configurations based on the scientific objectives of the study rather than assuming that additional channels or more complex hardware will always improve experimental outcomes. Standardized placement systems and transparent reporting further support reproducibility and meaningful comparison across studies.

Continue Building Your EEG Study

Choosing where to record brain activity is only one aspect of modern EEG research. Increasingly, researchers are also deciding where experiments themselves should take place.

In the next guide, Mobile EEG Research: Studying the Brain Beyond the Laboratory, we'll explore how wireless EEG is expanding cognitive neuroscience into classrooms, workplaces, healthcare environments, and other real-world settings while balancing ecological validity with experimental control.

Suggested Reading

References

[1] Sahar, N. S., Safri, N. M., & Zakaria, N. A. (2022). Use of EEG technique in a cognitive process study-a review. ELEKTRIKA-Journal of Electrical Engineering, 21(2), 24-32.

[2] Nastase, S. A., Goldstein, A., & Hasson, U. (2020). Keep it real: rethinking the primacy of experimental control in cognitive neuroscience. NeuroImage, 222, 117254. https\://doi.org/10.1016/j.neuroimage.2020.117254

[3] García‐Monge, A., Rodríguez‐Navarro, H., Bores‐García, D., & González‐Calvo, G. (2024). Electroencephalography in naturalistic and semi‐naturalistic educational contexts: A systematic review. Review of Education, 12(3), e70020. https\://doi.org/10.1002/rev3.70020

Introduction

The placement of EEG electrodes influences the types of neural activity researchers can observe and how experimental findings are interpreted. While selecting an EEG system is an important part of study planning, deciding where to record brain activity is equally critical. Electrode placement should always be guided by the research question rather than convenience or hardware specifications.

Different cognitive processes engage different brain regions, and no single electrode configuration is appropriate for every study. Researchers investigating visual perception may prioritize occipital regions, while studies of executive function often emphasize frontal activity. Other experiments may require broad cortical coverage to explore distributed neural networks.

This guide introduces common EEG electrode placement systems, explains how montages influence data collection, and discusses practical considerations for selecting recording locations that support the scientific objectives of a study.

Understanding Electrode Placement

EEG electrodes detect changes in electrical potential at the scalp generated by underlying neural activity. Because these signals are measured from multiple locations across the head, electrode placement determines which regions of cortical activity are sampled during an experiment.

Most EEG research follows standardized placement systems that allow recordings to be reproduced and compared across laboratories. Consistent electrode positioning also improves collaboration and facilitates interpretation of published findings.

Rather than attempting to measure every possible brain region, researchers should select electrode locations that best address their experimental hypotheses while considering practical constraints such as participant comfort, setup time, and recording quality.

The International 10-20 System

The International 10-20 System is the most widely used framework for positioning EEG electrodes. It defines standardized recording locations based on anatomical landmarks and proportional distances across the scalp, allowing researchers to reproduce electrode placement consistently across participants and studies [1].

Electrode labels correspond to general cortical regions. Frontal electrodes are identified with F, central with C, parietal with P, occipital with O, and temporal with T. Midline electrodes include the letter z, while odd numbers represent locations on the left hemisphere and even numbers indicate corresponding positions on the right.

Using standardized placement systems improves communication between researchers and helps ensure that published findings can be replicated using comparable recording configurations.

Top-down diagram of a head showing EEG electrode positions in the 10-20 system, color-coded by frontal, central, parietal, temporal and occipital regions, with a nasion-to-inion scale marking the 10% and 20% spacing intervals.

Label

Scalp region

Commonly studied in

Example sites

F

Frontal

Executive function, attention, decision-making

F3, F4, Fz

C

Central

Sensorimotor processes

C3, C4, Cz

P

Parietal

Attention, spatial processing, working memory

P3, P4, Pz

O

Occipital

Visual processing

O1, O2

T

Temporal

Auditory and language processing

T7, T8

z (suffix)

Midline

Activity along the scalp's center line

Fz, Cz, Pz

Odd number

Left hemisphere

Left-side counterpart of a site

F3, P7, O1

Even number

Right hemisphere

Right-side counterpart of a site

F4, P8, O2

Choosing Electrode Locations Based on the Research Question

Electrode selection should always begin with the scientific question rather than the available hardware.

Studies investigating visual processing often prioritize occipital electrodes because these regions are closely associated with visual information processing. Research involving executive function, attention, and decision-making frequently focuses on frontal regions, while sensorimotor studies may emphasize central electrodes.

Some experiments require broad cortical coverage because multiple brain regions contribute to the cognitive process under investigation. Others may focus on a smaller set of strategically selected electrodes when the neural mechanisms are already well understood.

Matching electrode placement to the experimental objectives improves both recording efficiency and interpretation of the resulting data.

Understanding Montages

A montage describes how EEG signals are referenced and displayed during recording or analysis. Although electrode placement determines where signals are collected, the selected montage influences how those signals are compared and interpreted.

Common reference strategies include common reference, average reference, linked mastoids, and bipolar montages. Each approach offers advantages depending on the experimental design and research objectives [1].

Because different reference strategies may influence waveform appearance, researchers should document the selected montage clearly when reporting experimental methods.

Four head diagrams comparing EEG montage types: common reference, average reference, linked mastoids and bipolar, each showing how its electrodes are connected.

Reference strategy

Each channel is compared against

Strengths

Watch out for

Common reference

A single shared electrode

Simple, consistent across channels

Activity at the reference site appears in every channel

Average reference

The mean of all recording electrodes

No single reference site dominates

Works best with dense, even coverage; less suited to low channel counts

Linked mastoids

The average of both mastoid sites

Widely used in ERP research; eases comparison with published work

Mastoids are not fully neutral and can pick up muscle activity

Bipolar

An adjacent electrode, in chained pairs

Highlights local differences between neighboring sites

Suppresses activity shared across neighboring electrodes

Channel Count and Spatial Coverage

Researchers often assume that increasing the number of electrodes automatically improves data quality. In practice, the appropriate channel count depends on the scientific objectives of the study.

Experiments investigating broad cortical networks or spatial patterns of neural activity may benefit from greater electrode coverage. Other studies, particularly those focusing on well-characterized cognitive processes or applied human factors research, may obtain meaningful results using fewer recording channels when those channels are positioned appropriately.

Selecting more electrodes than necessary increases setup time, participant burden, and data processing requirements without always providing additional scientific value.

The most effective recording strategy balances spatial coverage with the practical requirements of the experiment.

Electrode Placement in Mobile EEG Research

Wireless EEG has expanded opportunities to investigate cognition outside traditional laboratory environments. Mobile recording introduces additional practical considerations because participant movement, comfort, and recording duration become increasingly important.

Researchers designing classroom studies, workplace assessments, field research, or other naturalistic experiments often prioritize recording configurations that combine stable signal quality with efficient setup and participant comfort [2], [3].

Selecting an electrode configuration that supports both the scientific objectives and the recording environment helps maximize data quality throughout the study.

Matching the EEG System to the Study

After determining the required electrode locations and overall recording strategy, researchers can select an EEG system that supports those methodological needs.

Studies requiring rapid deployment or streamlined experimental workflows may benefit from systems with fewer electrodes positioned to capture commonly investigated cortical regions. Research requiring broader spatial coverage, event-related potentials, or more advanced cognitive analyses may benefit from systems that support additional recording channels and greater flexibility.

Rather than asking which EEG system is the most advanced, researchers should consider which system best supports the experimental questions they intend to answer.

System

Recording channels

Recording sites

Reference placement

Insight

5

AF3, AF4, T7, T8, Pz

CMS/DRL on left mastoid

Epoc X

14

AF3, F7, F3, FC5, T7, P7, O1, O2, P8, T8, FC6, F4, F8, AF4

CMS/DRL at P3/P4 (mastoids as alternative)

EPOC X PRO

16

Epoc X's 14 sites plus P3 and P4

CMS left mastoid, DRL right mastoid (fixed)

Flex 2 (Saline or Gel)

Up to 32, configurable

Any of 74 cap openings at standard 10-20 positions

CMS/DRL at any 10-20 location or on the ears

Side-by-side head diagrams of the EPOC X and EPOC X PRO electrode layouts, with the two added P3 and P4 sensors highlighted in blue to show the PRO’s added parietal and visual coverage.

Reporting Electrode Placement

Transparent reporting is an essential component of reproducible EEG research. Researchers should document the electrode placement system, recording montage, reference strategy, channel configuration, and any deviations from standardized placement procedures.

Providing this information allows other investigators to evaluate the methodology, reproduce the experiment, and compare findings across studies.

Clear methodological reporting strengthens both individual studies and the broader scientific literature.

Key Takeaways

Electrode placement is a fundamental component of experimental design. Choosing appropriate recording locations and montages helps ensure that EEG data accurately reflect the cognitive processes being investigated.

Researchers should select electrode configurations based on the scientific objectives of the study rather than assuming that additional channels or more complex hardware will always improve experimental outcomes. Standardized placement systems and transparent reporting further support reproducibility and meaningful comparison across studies.

Continue Building Your EEG Study

Choosing where to record brain activity is only one aspect of modern EEG research. Increasingly, researchers are also deciding where experiments themselves should take place.

In the next guide, Mobile EEG Research: Studying the Brain Beyond the Laboratory, we'll explore how wireless EEG is expanding cognitive neuroscience into classrooms, workplaces, healthcare environments, and other real-world settings while balancing ecological validity with experimental control.

Suggested Reading

References

[1] Sahar, N. S., Safri, N. M., & Zakaria, N. A. (2022). Use of EEG technique in a cognitive process study-a review. ELEKTRIKA-Journal of Electrical Engineering, 21(2), 24-32.

[2] Nastase, S. A., Goldstein, A., & Hasson, U. (2020). Keep it real: rethinking the primacy of experimental control in cognitive neuroscience. NeuroImage, 222, 117254. https\://doi.org/10.1016/j.neuroimage.2020.117254

[3] García‐Monge, A., Rodríguez‐Navarro, H., Bores‐García, D., & González‐Calvo, G. (2024). Electroencephalography in naturalistic and semi‐naturalistic educational contexts: A systematic review. Review of Education, 12(3), e70020. https\://doi.org/10.1002/rev3.70020

Introduction

The placement of EEG electrodes influences the types of neural activity researchers can observe and how experimental findings are interpreted. While selecting an EEG system is an important part of study planning, deciding where to record brain activity is equally critical. Electrode placement should always be guided by the research question rather than convenience or hardware specifications.

Different cognitive processes engage different brain regions, and no single electrode configuration is appropriate for every study. Researchers investigating visual perception may prioritize occipital regions, while studies of executive function often emphasize frontal activity. Other experiments may require broad cortical coverage to explore distributed neural networks.

This guide introduces common EEG electrode placement systems, explains how montages influence data collection, and discusses practical considerations for selecting recording locations that support the scientific objectives of a study.

Understanding Electrode Placement

EEG electrodes detect changes in electrical potential at the scalp generated by underlying neural activity. Because these signals are measured from multiple locations across the head, electrode placement determines which regions of cortical activity are sampled during an experiment.

Most EEG research follows standardized placement systems that allow recordings to be reproduced and compared across laboratories. Consistent electrode positioning also improves collaboration and facilitates interpretation of published findings.

Rather than attempting to measure every possible brain region, researchers should select electrode locations that best address their experimental hypotheses while considering practical constraints such as participant comfort, setup time, and recording quality.

The International 10-20 System

The International 10-20 System is the most widely used framework for positioning EEG electrodes. It defines standardized recording locations based on anatomical landmarks and proportional distances across the scalp, allowing researchers to reproduce electrode placement consistently across participants and studies [1].

Electrode labels correspond to general cortical regions. Frontal electrodes are identified with F, central with C, parietal with P, occipital with O, and temporal with T. Midline electrodes include the letter z, while odd numbers represent locations on the left hemisphere and even numbers indicate corresponding positions on the right.

Using standardized placement systems improves communication between researchers and helps ensure that published findings can be replicated using comparable recording configurations.

Top-down diagram of a head showing EEG electrode positions in the 10-20 system, color-coded by frontal, central, parietal, temporal and occipital regions, with a nasion-to-inion scale marking the 10% and 20% spacing intervals.

Label

Scalp region

Commonly studied in

Example sites

F

Frontal

Executive function, attention, decision-making

F3, F4, Fz

C

Central

Sensorimotor processes

C3, C4, Cz

P

Parietal

Attention, spatial processing, working memory

P3, P4, Pz

O

Occipital

Visual processing

O1, O2

T

Temporal

Auditory and language processing

T7, T8

z (suffix)

Midline

Activity along the scalp's center line

Fz, Cz, Pz

Odd number

Left hemisphere

Left-side counterpart of a site

F3, P7, O1

Even number

Right hemisphere

Right-side counterpart of a site

F4, P8, O2

Choosing Electrode Locations Based on the Research Question

Electrode selection should always begin with the scientific question rather than the available hardware.

Studies investigating visual processing often prioritize occipital electrodes because these regions are closely associated with visual information processing. Research involving executive function, attention, and decision-making frequently focuses on frontal regions, while sensorimotor studies may emphasize central electrodes.

Some experiments require broad cortical coverage because multiple brain regions contribute to the cognitive process under investigation. Others may focus on a smaller set of strategically selected electrodes when the neural mechanisms are already well understood.

Matching electrode placement to the experimental objectives improves both recording efficiency and interpretation of the resulting data.

Understanding Montages

A montage describes how EEG signals are referenced and displayed during recording or analysis. Although electrode placement determines where signals are collected, the selected montage influences how those signals are compared and interpreted.

Common reference strategies include common reference, average reference, linked mastoids, and bipolar montages. Each approach offers advantages depending on the experimental design and research objectives [1].

Because different reference strategies may influence waveform appearance, researchers should document the selected montage clearly when reporting experimental methods.

Four head diagrams comparing EEG montage types: common reference, average reference, linked mastoids and bipolar, each showing how its electrodes are connected.

Reference strategy

Each channel is compared against

Strengths

Watch out for

Common reference

A single shared electrode

Simple, consistent across channels

Activity at the reference site appears in every channel

Average reference

The mean of all recording electrodes

No single reference site dominates

Works best with dense, even coverage; less suited to low channel counts

Linked mastoids

The average of both mastoid sites

Widely used in ERP research; eases comparison with published work

Mastoids are not fully neutral and can pick up muscle activity

Bipolar

An adjacent electrode, in chained pairs

Highlights local differences between neighboring sites

Suppresses activity shared across neighboring electrodes

Channel Count and Spatial Coverage

Researchers often assume that increasing the number of electrodes automatically improves data quality. In practice, the appropriate channel count depends on the scientific objectives of the study.

Experiments investigating broad cortical networks or spatial patterns of neural activity may benefit from greater electrode coverage. Other studies, particularly those focusing on well-characterized cognitive processes or applied human factors research, may obtain meaningful results using fewer recording channels when those channels are positioned appropriately.

Selecting more electrodes than necessary increases setup time, participant burden, and data processing requirements without always providing additional scientific value.

The most effective recording strategy balances spatial coverage with the practical requirements of the experiment.

Electrode Placement in Mobile EEG Research

Wireless EEG has expanded opportunities to investigate cognition outside traditional laboratory environments. Mobile recording introduces additional practical considerations because participant movement, comfort, and recording duration become increasingly important.

Researchers designing classroom studies, workplace assessments, field research, or other naturalistic experiments often prioritize recording configurations that combine stable signal quality with efficient setup and participant comfort [2], [3].

Selecting an electrode configuration that supports both the scientific objectives and the recording environment helps maximize data quality throughout the study.

Matching the EEG System to the Study

After determining the required electrode locations and overall recording strategy, researchers can select an EEG system that supports those methodological needs.

Studies requiring rapid deployment or streamlined experimental workflows may benefit from systems with fewer electrodes positioned to capture commonly investigated cortical regions. Research requiring broader spatial coverage, event-related potentials, or more advanced cognitive analyses may benefit from systems that support additional recording channels and greater flexibility.

Rather than asking which EEG system is the most advanced, researchers should consider which system best supports the experimental questions they intend to answer.

System

Recording channels

Recording sites

Reference placement

Insight

5

AF3, AF4, T7, T8, Pz

CMS/DRL on left mastoid

Epoc X

14

AF3, F7, F3, FC5, T7, P7, O1, O2, P8, T8, FC6, F4, F8, AF4

CMS/DRL at P3/P4 (mastoids as alternative)

EPOC X PRO

16

Epoc X's 14 sites plus P3 and P4

CMS left mastoid, DRL right mastoid (fixed)

Flex 2 (Saline or Gel)

Up to 32, configurable

Any of 74 cap openings at standard 10-20 positions

CMS/DRL at any 10-20 location or on the ears

Side-by-side head diagrams of the EPOC X and EPOC X PRO electrode layouts, with the two added P3 and P4 sensors highlighted in blue to show the PRO’s added parietal and visual coverage.

Reporting Electrode Placement

Transparent reporting is an essential component of reproducible EEG research. Researchers should document the electrode placement system, recording montage, reference strategy, channel configuration, and any deviations from standardized placement procedures.

Providing this information allows other investigators to evaluate the methodology, reproduce the experiment, and compare findings across studies.

Clear methodological reporting strengthens both individual studies and the broader scientific literature.

Key Takeaways

Electrode placement is a fundamental component of experimental design. Choosing appropriate recording locations and montages helps ensure that EEG data accurately reflect the cognitive processes being investigated.

Researchers should select electrode configurations based on the scientific objectives of the study rather than assuming that additional channels or more complex hardware will always improve experimental outcomes. Standardized placement systems and transparent reporting further support reproducibility and meaningful comparison across studies.

Continue Building Your EEG Study

Choosing where to record brain activity is only one aspect of modern EEG research. Increasingly, researchers are also deciding where experiments themselves should take place.

In the next guide, Mobile EEG Research: Studying the Brain Beyond the Laboratory, we'll explore how wireless EEG is expanding cognitive neuroscience into classrooms, workplaces, healthcare environments, and other real-world settings while balancing ecological validity with experimental control.

Suggested Reading

References

[1] Sahar, N. S., Safri, N. M., & Zakaria, N. A. (2022). Use of EEG technique in a cognitive process study-a review. ELEKTRIKA-Journal of Electrical Engineering, 21(2), 24-32.

[2] Nastase, S. A., Goldstein, A., & Hasson, U. (2020). Keep it real: rethinking the primacy of experimental control in cognitive neuroscience. NeuroImage, 222, 117254. https\://doi.org/10.1016/j.neuroimage.2020.117254

[3] García‐Monge, A., Rodríguez‐Navarro, H., Bores‐García, D., & González‐Calvo, G. (2024). Electroencephalography in naturalistic and semi‐naturalistic educational contexts: A systematic review. Review of Education, 12(3), e70020. https\://doi.org/10.1002/rev3.70020

Continue reading

How to Choose the Right EEG System for Your Research